How to Apply DIY Lash Clusters at Home: Step-by-Step Guide

LASHYTOUCH 144 lash clusters set with bond & sealant, remover and tweezers for applying lash clusters at home

Quick answer: clean and dry your natural lashes, then place each cluster under your lashes, close to the lash line but not on the skin. With self-adhesive (Press & Go) clusters, you simply press each one for a few seconds. With glue-based clusters, you use a bond & sealant. Once you get the hang of it, a full set takes about 5 minutes.

DIY lash clusters give you the soft, full look of salon extensions without the appointment. This guide walks you through both routines - self-adhesive and glue-based - step by step, plus how to take your lashes off without pulling on your natural ones.

What you need

Before you start

  • Do a patch test before your first full application. Apply a small amount of the bond - or the band of one self-adhesive cluster - to the skin behind your ear or on your inner arm and leave it for 24 hours. If you notice redness, itching or swelling, don't use the product near your eyes.
  • Start with clean, dry lashes. Oily cleansers, eye creams and oil-based makeup near the lash line stop clusters from gripping.
  • Contact lenses go in first, then your lashes.
  • Mascara is optional. Apply clusters on clean lashes or over one thin coat. Avoid heavy or oil-based formulas.

How to apply self-adhesive (Press & Go) clusters

The adhesive is already on the cluster, so there is no separate glue step. The thin black base blends into your lash line like a soft line of eyeliner.

  1. Plan your look. Use the lash map in your kit: shorter clusters toward the inner corner, longer ones toward the outer corner. Not sure where to start? Read our lash mapping guide.
  2. Pick up one cluster with tweezers or your fingertips, holding it by the lashes, not the base.
  3. Place it under your natural lashes, close to the lash line but not on the skin.
  4. Press firmly for a few seconds so it grips. Pressing each cluster well is the secret to a good hold.
  5. Repeat across the eye, leaving small gaps at first. You can always add more.

How to apply glue-based clusters (Bond & Seal)

The glue-based routine gives you full control over every step. Follow the directions that come with your bond & sealant - the basic flow looks like this:

  1. Prep clean, dry lashes and lay out your clusters according to your lash map.
  2. Apply the bond & sealant to the underside of your natural lashes, keeping it on the lashes and away from the eye and skin.
  3. Place each cluster under your natural lashes with tweezers, close to the lash line but not on the skin.
  4. Gently pinch your natural lashes and the cluster together with the tweezers so they hold as one.
  5. Let the bond set fully before water, sweat or rubbing.

Practice makes this quick: once you have done it a few times, a full set takes about 5 minutes.

How to remove lash clusters safely

Go gently and never tug at your natural lashes.

  • Self-adhesive clusters: lift each cluster off slowly and put it back in the case. You can wear it again, no glue needed.
  • Glue-based clusters: apply an oil-based remover (like the one in our Pro Care Kit) along the band, wait a few seconds for the bond to soften, then slide the cluster off. Cleanse your lashes afterwards. To reuse a glue-based cluster, clean off any leftover bond, let it dry and store it in the case.

Troubleshooting

  • A cluster is lifting. Press it back, or replace just that one. Oil from skin and skincare is the most common cause - keep oil-based products away from the lash line.
  • The base feels scratchy. The cluster is sitting on the skin. Take it off and place it a little higher, under the lashes.
  • Your eyes feel irritated. Remove the lashes right away. If irritation continues, check with your doctor or optometrist.

Frequently asked questions

How long do lash clusters last?

Customers tell us their self-adhesive clusters stay on for 2-3 days. How long yours last depends on your natural lashes, skin oils, water, rubbing and your routine.

Can I shower or work out with lash clusters?

Give the bond time to set fully first. After that, a shower or a workout is usually fine. Pat your lashes dry instead of rubbing.

Will DIY lashes damage my natural lashes?

Applied and removed gently, they shouldn't. Lift self-adhesive clusters off slowly, use an oil-based remover for glue-based clusters, and give your natural lashes a rest day now and then.

Ready to try it? Shop LASHYTOUCH lash clusters - every style was tested by a Toronto lash artist before it made the case. Free shipping across Canada on orders of $50 and up.